七妹福利500福利

全国服务热线:021-57293980 51855511
 
中文 / ENGLISH   
 
关于我们
公司简介
七妹福利500福利
公司理念
辉煌历程
主要荣誉
工作机会
检测中心
联系我们
联系我们
     
 

上海基地:

七妹福利500福利(总部)

全国免费服务热线:

13371811158

联系人:尚伟

Tel:+86(0)21 5729 3980

七妹福利500福利    +86(0)21 5185 5511

Fax:+86(0)21 5729 1585

七妹福利500福利Mail:info@rentnepa.com

Add:上海市金山区金山卫镇漕廊公路6033号(金石公路口)

Zip:201515

七妹福利500福利(天津)有限公司

七妹福利500福利天津上热金属科技有限公司

天津上热真空七妹福利500福利有限公司

七妹福利500福利Add:天津市宝坻区黄庄镇产业功能区一号路9号

联系人:

左孝进  Mb:13821357588

Mail:xiaojin.zuo@rentnepa.com

王思斌  Mb:18822112007

Mail:sibin.wang@rentnepa.com

湘潭基地:

湘潭上热金属七妹福利500福利有限公司

七妹福利500福利Tel:+86(0)731 5236 2532

七妹福利500福利Fax:+86(0)731 5236 2532

七妹福利500福利谭秋云 Mb:15873146116

Add:湖南省湘潭市九华工业区九华大道9号

Zip:411201

 
  您现在的位置:网站七妹福利500福利-技术中心
 
气体氮化和离子氮化之比较  2011/4/15 
 
分享到:
 
 

Gas Nitride or Plasma Nitride. Well known heat treat consultant David Pye, davidpye@pyemet.com is providing us with some details about what to consider when choosing between Gas or Plasma Nitriding. April 11/11

The choice between gas nitriding and plasma nitriding is usually a very difficult choice to make. The choice will come down to depend on;

  • Capital investment,

  • Logistics

  • Necessary surface metallurgy and control that is required for the processed component.

Capital Investment: The capital investment always seems to be considered as the driving force for the decision. Yes, the plasma systems are more costly than with the gas nitride. That is a correct assumption. But that seems to be where it stops. When making the cost comparison, between the two process techniques will generally be finished at the purchase price line. To have a true cost comparison, one really needs to consider the cost comparison of operating costs as well as the primary investment. It will then come down to considering the corporate amortization period of depreciation. After that, it really comes down to the operating costs. Once the equipment is amortized then it comes down to the direct operating costs of the equipment. It will be seen, that after the amortization period is complete, and then operating costs of the plasma technology are reduced, because of the nature of the process. This is because of process gas usage and power costs are lower. The writer has experienced the following approximate value to obtain a conventional nitrided case, as being;

  • 100ft³ of ammonia gas for 100ft² (approximate) of available surface area. (This is based on 5 to 7 process gas volume changes per hour). It further considers process temperature and time at process temperature. The reason for the process gas volume on gas nitriding being high is simply because the process vessel is being pressurized to a slight positive atmospheric pressure to act as a ‘sweep gas’ to ensure process gas circulation within the process retort and work.

  • 3 ft³ of process gas per hour (approximately)(nitrogen and hydrogen) for 100ft² work surface area. The reason for the low flow volume is because we are only using the gas necessary to generate the activity within plasma glow seam.

Logistics

The logistics consideration will be based on the;

  • Should the process be conducted ‘in house’ or sub-contracted out to a commercial heat treater, and why?

  • What is the distance of travel from the manufacturing house to the heat treatment shop?

  • Do we have the equipment to enable us to observe and control the surface metallurgy achievable. (Laboratory sample evaluation equipment)?

  • How quickly will the processed part  be processed by the commercial heat treater?

  • Do we have the appropriate floor space to accommodate the equipment?

  • Can we maintain and service the equipment?

Process evaluation

The question is now, how to test, evaluate, and most importantly, how do we control the process? A small metallurgical laboratory can be developed (or it is a  pre-existing laboratory) for the process evaluation that would include the following equipment;

  • Abrasive sample cut off saw

  • A pre-grind system for rough grind with silicon carbide papers

  • A rough polish using silicon carbide papers

  • Final polish using the appropriate grade of polishing cloth and either an aluminum slurry or diamond paste

  • Micro-hardness test unit

  • Inverted metallurgical microscope

  • Sample storage dessicator

  • Fume hood for simple acid etching

  • Spill kit

The above will enable you to process most metallurgical samples and not just nitride evaluation. The process control will come from the furnace control panel and its method of;

  • Data acquisition

  • Data storage

  • Gas delivery through either micrometer gas flow valves or mass flow controllers

  • Process gas  flow ratios

  • Temperature control

  • Time cycle control

  • Heating power control

The above is just some of control parameters that should be observed. Nitriding (gaseous or plasma) process parameters  need to be controlled if we are to produce continuous surface metallurgy and reproducible results.

 
 
      
Copyright 2011-2016 SUNRAY GROUP, LIMITED沪ICP备11022038号